Resistance Ranger Dual Wire Constant Monitors

The Resistance Ranger Constant Monitors are an accurate and cost effective system to ensure that an ESD workstation station is grounded. The system continually monitors the resistance levels of wrist strap sets and alarm to indicate a failure.  The system uses superior dual wire wrist straps that provide two paths-to-ground to ensure ESD protection. The Rangers can also monitor the ground connection of the ESD worksurfaces and grounded tools.  All three models have conductive cases and use an ultra-low voltage sensing current. The Resistance Rangers are designed for use in the most sensitive environments and processes.

Three Models:       

RangerOneâ„¢ – p/n CM1601:   
This model is simplest and most economical constant monitor. It monitors the resistance of 1 person/wrist strap. Also provides a second unmonitored ground jack.

RangerTwoâ„¢ – p/n CM1602:   
This model monitors the resistance level of 1 person/wrist strap and the worksurface ground. Also provides a second unmonitored ground jack.

Rangerâ„¢ – p/n CM1600:   
Ranger is the premiere work station grounding system available. The Ranger monitors two wrist bands, two work surfaces, and two auxiliary grounds simultaneously. Also provides two additional unmonitored ground jacks .The Ranger has an output to hookup to an external alarm. The monitor is enclosed in a stainless steel conductive case.

Calibration
The Ranger Series is factory calibrated and does not require annual recalibration.  It is recommended to verify the monitors are in proper working order with the CM2015PV periodic verification unit.

Accessories
Cyclops^TM Operator Presence Check – CMREMOTE-IR
The Cyclops is an infrared sensor that causes the monitor to alarm when an operator approaches the workstation without connecting their wrist strap. The alarm continues until compliance is achieved.

CP3000 Wrist Strap Parking Station
Provides a jack that will allow an operator to disconnect and leave the dual conductor cord at the workstation without the wrist strap monitoring system alarm sounding. For use with mono plug coil cords.

Superior Technology
Resistance based monitoring is the only true wrist strap monitoring technology available.  Single wire systems simply detect that a person is wearing a wrist strap and put the monitor into an unalarmed state.  Resistance monitors actually measure the resistance of the wrist strap in combination with the person and alarm if the product exceeds preset levels. This accurate measurement ensures reliability.

Compatible Wrist Straps
WB2800 Series Two Snap, Dual Wire Wrist Bands
WB2695 Series One Snaps Dual Wire Wrist Bands
WB5000 Series Mono Plug Dual Wire Metal Wrist Bands
WB7000 Series Mono Plug Dual Wire Fabric Wrist Bands
*Most Standard Dual Wire Wrist Band Sets are Compatible with the CM1600, CM1601 and CM1602

For price and availability on the Ranger series constant monitors or for information on any products in Transforming Technologies full line of ESD products, please call 419-841-9552 or email info@transforming-technologies.com.

Transforming Technologies is proud to announce the addition of the GrooveSTAT ESD Conductive Floor Runner to our line of ESD Products.

Transforming Technologies GrooveSTAT Conductive Rubber Matting provides the electrical properties specified by ESDA standards for floor mats. A ribbed emboss provides a non-slip surface that provides excellent traction and allows the mat to be easily cleaned. The ribbed matting is also very resilient, allowing it to stand up to heavy foot traffic while still maintaining its ESD protection. The material also offers moderate chemical resistance. The matting is 1/8″ thick matting is available in 4’x32′ rolls and an assortment of lengths.For use with ESD footwear such as heel grounders and sole grounders.

Meets or exceeds requirements of ANSI ESD-S20.20 and the recommendations of ESD STM7.1

Benefits & Features of the Transforming Technologies GrooveSTAT ESD Conductive Floor Runner:

• 100% conductive rubber: 10^3-10^5
• Corrugated v-groove surface allows for a superior traction and can easily be cleaned
• Available in rolls or an assortment of lengths.

Specifications of the Transforming Technologies conductive GrooveSTAT ESD Conductive Floor Runner:

• Point-to-point resistance: 10e3-10e5
• Mats or full rolls for floor runners
• Meet or exceeds requirements of ANSI ESD-S20.20 and the recommendations of ESD STM7.1

Transforming Technologies is proud to announce the addition of the ComfortTREAD Diamond Plate Anti-Fatigue Runner to our line of ESD Products.

ComfortTREAD diamond-plate ESD anti-fatigue mats keep your workers comfortable and your ESD sensitive equipment safe. The 100% conductive rubber mats are embossed with raised diamond-plate treads for superior traction and feature wide beveled borders to promote safety. A fully molded honeycombed cell design absorbs shock and cushions the feet from constant contact with hard surfaces. The mat will not separate, bubble-up, ripple, tear, compress or lose resiliency. Available in interlocking sections which can be quickly dismantled to make moving and cleaning easy. Two FM9E connected creates a 2.5′ x5′ workstation mat or you can pair the two FM9E with any number of FM9C pieces to create a runner in 30” increments. For use with ESD footwear such as heel grounders and sole grounders.

Meets or exceeds requirements of ANSI ESD-S20.20 and the recommendations of ESD STM7.1

Benefits & Features of the Transforming Technologies ComfortTREAD ESD Matting:

• 100% conductive rubber: 10^3-10^5
• Diamond-plate treads for superior traction
• Interlocking sections create a 5’ long work-station mat or runners in 30” increments.
• Beveled borders for safety

Specifications of the Transforming Technologies conductive ComfortTREAD ESD Matting:

• Point-to-point resistance: 10e3-10e5
• Inlocking mats for floor runners
• Meet or exceeds requirements of ANSI ESD-S20.20 and the recommendations of ESD STM7.1

ComfortTREAD Anti-Fatigue Interlocking Piece

ComfortTREAD Anti-Fatigue End Piece

For price and availability on the FM9 ComfortTREAD Anti-Fatigue Floor Runners or for information on any products in Transforming Technologies full line of ESD products, please call 419-841-9552 or email info@transforming-technologies.com.

Ionizers remove static from surfaces that cannot be grounded. You will find two common types: AC or Alternating Current and DC or Direct Current. This presentation reviews the pros and cons of each technology and will help you decide which ionizer will work best for your application.

For more information, contact Transforming Technologies 419-841-9552.